Black and Decker 8 1 4 Compound Miter Saw 9425

IMf

IC&DEGKER.

Instruction Manual

8W' Compound Miter Saw

9425

.322765

Summary of content (12 pages)

• PAGE 1

  IMf IC&DEGKER. Instruction Manual 8W' Compound Miter Saw 9425 .

• PAGE 2

  Welcome to Black & Decker's wonderful world of PowerTools. If you already own a Black & Decker Power Tool you know the plea­ sures a high quality, high perforrhance power tool can deliver. Your new Compound Miter Saw has been carefully engineered and built to Black & Decker's high standards for quality and dependability. It's built to last for many years of tough, trouble-free service and high quality performance. It can cut wood, plastics and com­ positions.

• PAGE 3

  SAFETY INSTRUCTIONS WARNING: When using Electric Tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 4.

• PAGE 4

  Additional Safety Rules For The Compound Miter Saw 1. DO — Protect line with at least a 15 ampere time delay fuse. 2. DO — Make certain the balde rotates in the correct direction. 3. DO — Be sure all clamp handles are tight before starting any operation. 4. DO — Be sure blade and arbor col­ lars are clean and recessed side of collars are against blade. Tighten arbor screw securely. 5. DO — Keep saw blade sharp and properly set. 6. DO — Keep motor air slots clean and free of chips. 7.

• PAGE 5

  Setup FAMiLiARiZATION: Place the Miter Saw on a flat, strong and level surface, and examine it to become familiar with the terminology used to describe its var­ ious parts. (See Figures 1 and 2.) UNLOCKING THE PIVOT ARM: Your saw was shipped from the factory with the pivot arm in the locked down position This position is used to facilitate packaging and for storage.

• PAGE 6

  An alternate mounting nnethod that will enhance the s a w s portability is to mount the saw on a piece of 1 /2" or thicker plywood. The saw can then be taken to remote locations and the ply­ wood clamped in place with a couple of large "C" damps. 4. The miter scale is graduated in incre­ ments of one degree {1 °). The exam pie shown in Figure 7 is 35^, Miter Table and Miter Scale The miter table and miter scale permit you to set accurate miters up to 45° left or right.

• PAGE 7

  Cutting Tips Lower Blade Guard Miter Clamp Knob WEAR EYE PROTECTION. The smoothness of any cut de­ pends on a number of variables. Things like materia! being cut. blade type, blade sharpness and rate of cut all combine to affect the quality of the cut. When cutting framing lumber or other types of lumber where cut smooth­ ness IS not a point of concern, high cut­ ting rate coupled with a sharp general purpose blade will produce satisfactory results.

• PAGE 8

  6. Remove the old blade and insiall the new one taking care to orient the two blade washers carefully, as shown in Figure 13. piiillliiiililiiiK The example in Figure A is a joint made by using the bevel adjustment to bevel the edges of the boards (at 45° each) to form a 90° miter corner. For this operation, set the bevel post adjustment at 45° and the miter table adjustment at 0°. Position the wood with the broad flat side against the table and the narrow edge against the fence.

• PAGE 9

  Cutting Crown Molding Your Compound Miter Saw is probably better suited to the difficult task of cut­ ting crown molding than any other tool made. In order to fit properly, crown mold­ ing must be compound mitered with extreme accuracy (see Figure 17). The two surfaces on a piece of crown molding that fit flat against the ceiling and the wail of a room are at angles that, when added together, equal exactly 90"^.

• PAGE 10

  Accessories The accessories fisted in this manual are available at extra cost from your local dealer or Black & Decker Service Center. A complete listing of service centers is included on the owner's registration card packed with your tool. If you need assistance in locating any accessory please contact: Black & Decker (U.S.) Inc. User Services Department 10 North Park Drive P.O. Box 857 Hunt Valley. MD 21030>0857 Saw Biades Cat. No.

• PAGE 11

  NOTES

• PAGE 12

  Black & Decker's Full Two Year Home Use Warranty states that, in case of a defect, you may return the tool to the place of purchase for a free replacement (if it is a participating retailer) or you may take it to a Black & Decker Service Center. Home Use Warranty (A Full Two Year Warranty) Black & Decker (U.S.) Inc. warrants this product for two years against any defects that are due to faulty material or workmanship.

Black and Decker 8 1 4 Compound Miter Saw 9425

Source: https://www.manualshelf.com/manual/black-decker/81-4-compund-miter-saw-9425/owner-manual-english.html

Share this post